Products



STANDARD SPECIFICATION
Pressed steel sectional water tanks (rectangular) constructed with hydraulically pressed flanged panels conform to B.S. 1564 and hot dip galvanized to ISO 1461:2009

Materials
Mild steel used in the plates, stays, cleats, and pads all conform to the requirements of BSEN10025:2004

Tank Panels
Tank panels of 4ft x 4ft or 1m x 1m square are hot dip galvanized to ISO 1461:1999

Tank Covers
Standard tank covers are hydraulically pressed 3.0mm / 1.5mm thk x 4ft x 4ft or 1m x 1m square and are hot dip galvanized.

Stays and Cleats
The sides and ends of all tanks shall be supported by stays at the junction of two or more plates. The stays and cleats shall be made from mild steel and hot dip galvanized.

Joining Compounds
Non-toxic, odorless PVC Foam Sealant and butyl sealant or equivalent shall be supplied.

Manhole and Vent
Each tank or compartment shall be supplied with one no. of 600mm square manhole and one 100mm diameter vent with insect proof attached on to tank cover.

Ladders
Hot dip galvanized ladder for tank internal and external are provided (aluminium ladder on request)

Level Indicator
Mild steel or galvanized indirect reading level indicator is provided on request.

B.S. 1564: 1975 (Revised)
For cold liquid with density of 1.0 and having temperature not exceeding 38°C. Tanks 4ft Height: Bottom, sides and ends. 5mm Tanks 8ft Height: Bottom, sides and ends. 5mm Tanks 12ft Height: Bottom, sides and ends. 5mm Tanks 16ft Height: Bottom and first tiers of sides and ends. 6mm Second, third and top tiers of sides & ends 5mm

PRESSED STEEL SECTIONAL PANEL TANK
Steel Hot Pressed Sectional Panel Tanks has an excellent corrosion-resistant panels, the surface of the tank is uniformly smooth without any mass growth, therefore enable long-term use as the panels inhibit the proliferation of bacteria and other various germs by perfectly blocking all light from outside. Sectional tank utilizes horizontal and vertical space at the maximum and those are suitable for tanks of large capacities. It operates a corner-type system.

Standard Thickness for 1.22m x 1.22m Tank Panel

TYPE 1.22M (H) 2.44M(H) 3.66M(H) 4.88M(H)
Side panels (4th) - - - 5mm
Side panels (3rd) - - 5mm 5mm
Side panels (2nd) - 5mm 5mm 5mm
Side panels (1st) 5mm 5mm 5mm 5mm
Bottom Panels 5mm 5mm 5mm 5mm

Standard Thickness for 1m x 1m Tank Panel

TYPE 1.0M (H) 2.0M(H) 3.0M(H) 4.0M(H) 5.0M(H)
Side panels (5th) - - - - 5mm
Side panels (4th) - - - 5mm 5mm
Side panels (3rd) - - 5mm 5mm 5mm
Side panels (2nd) - 5mm 5mm 5mm 5mm
Side panels (1st) 5mm 5mm 5mm 5mm 5mm
Bottom Panels 5mm 5mm 5mm 5mm 5mm




PRESSED STAINLESS STEEL SECTIONAL PANEL TANK


STANDARD SPECIFICATION
Pressed steel sectional water tank constructed with hydraulically pressed flanged panels, SS 304 & 316, which is match with QCS 2014 Standard

Materials
The tank panel, tie rods, stays and cleats are made from Stainless Steel Grade 304/316

Flanges of Plates:
Tank panels pressed with a 90 degree panel flange to the face of the plate on four sides

Bolts, Nuts and Washers
SS304/316 bolts, nuts and washer

Ladders
One Internal & External HDG ladder for 1.5 mtrs. height & above only

Skid Base
HDG C-Channels.

Jointing Materials
Non toxic PVC foam to be used for all jointing between tank panel flange

Tank Cover
Panel type tank cover supported by trusses 600mm x 600mm square manhole and supplied as standard for each compartment

PRESSED STAINLESS STEEL SECTIONAL PANEL TANK
Stainless steel Sectional Panel Tanks has an excellent corrosion-resistant panels, the surface of the tank is uniformly smooth without any mass growth, therefore enable long-term use as the panels inhibit the proliferation of bacteria and other various germs by perfectly blocking all light from outside. Sectional tank utilizes horizontal and vertical space at the maximum and those are suitable for tanks of large capacities. It operates a corner-type system.

Nozzels for Connection
Short pipe with flange or socket for all pipe connections

Finish
Hot Dip Galvanized conform to ISO 1461